對于氣液增壓泵設備，很多人沒有見過，但這種設備在我們的生活中很普遍。設備操作簡單可靠，只要基本遵守操作規程和注意事項就不會有任何隱患。為了讓更多人了解，先從問題說起，比如氣液增壓泵對氣源的要求。
For gas-liquid booster pump equipment, many people have not seen it, but this type of equipment is very common in our daily lives. The equipment operation is simple and reliable, as long as the basic operating procedures and precautions are followed, there will be no hidden dangers. In order to make more people understand, let's start with the problem, such as the requirements for the air source of the gas-liquid booster pump.
一般來說，氣動液體增壓泵對氣源的要求不高也不低。要求是過濾后干凈干燥的壓縮空氣，4~7 kg，不能太大也不能太小。在使用氣液增壓泵產品時，為了保證氣源能夠滿足這些要求，可以做以下處理，僅供參考：可以選擇自動排水三點組合，達到更好的空氣質量。如果氣壓不穩定，可以安裝儲氣罐，實現更穩定的氣源壓力供應。定期檢查氣動三聯油杯中的潤滑油量是否充足。定期給予三點聯合引流治療等。
Generally speaking, pneumatic liquid booster pumps have neither high nor low requirements for air sources. The requirement is clean and dry compressed air filtered, weighing 4-7 kg, which should not be too large or too small. When using gas-liquid booster pump products, in order to ensure that the air source can meet these requirements, the following treatment can be done for reference only: the automatic drainage three-point combination can be selected to achieve better air quality. If the air pressure is unstable, an air storage tank can be installed to achieve a more stable air supply pressure. Regularly check whether the lubricating oil in the pneumatic triple oil cup is sufficient. Regularly administer three point combined drainage treatment, etc.

如果氣源不好（水蒸氣、油氣、灰塵等），產品長期使用后會對產品內部造成不必要的影響，降低綜合使用壽命，這一點大家一定要注意。注意事項還有很多，如：使用前，建議在驅動氣源入口處加裝油水分離器，經常將水杯內的水放出；每次使用氣液增壓泵后，都要將相關氣體排出；定期檢查氣體增壓泵，以保持零件的完整性。
If the air source is not good (such as water vapor, oil gas, dust, etc.), long-term use of the product will cause unnecessary impact on the internal parts of the product, reducing its comprehensive service life. This is something that everyone must pay attention to. There are many precautions to note, such as: before use, it is recommended to install an oil water separator at the inlet of the driving air source, and frequently drain the water from the water cup; After each use of the gas-liquid booster pump, the relevant gas must be discharged; Regularly inspect the gas booster pump to maintain the integrity of the parts.
此外，還需要在使用前后進行檢查和維護，防止設備故障。比如泵突然停止工作，這時候就要找原因。操作方法可以包括檢查驅動氣源是否打開，驅動壓力是否符合要求；檢查氣缸蓋氣路是否暢通；檢查換向閥的氣路是否暢通；檢查換向閥端的針孔是否已成為正常通孔；檢查換向閥的高壓室有無泄漏。
In addition, it is necessary to conduct inspections and maintenance before and after use to prevent equipment malfunctions. For example, if the pump suddenly stops working, it is necessary to find the cause. The operation method can include checking whether the driving air source is open and whether the driving pressure meets the requirements; Check if the air circuit of the cylinder head is smooth; Check if the air circuit of the directional valve is smooth; Check if the pinhole at the reversing valve end has become a normal through-hole; Check the high-pressure chamber of the directional valve for leaks.
氣液增壓泵對氣源有什么要求？相關要求還是比較嚴格的，需要多加注意。
What are the requirements for air source for gas-liquid booster pumps? The relevant requirements are still quite strict and require more attention.